Instructions–Parts List
AIR OPERATED, SINGLE COMPONENT DISPENSE VALVE
308876K
1K Ultra–Litet
For dispensing a wide variety of single component sealants and adhesives.
4000 psi (28 MPa, 276 bar) Maximum Fluid Working Pressure
120 psi (0.84 MPa, 8.4 bar) Maximum Air Inlet Pressure
See page 2 for Table of Contents
Part No. 965766
Stainless Steel Wetted Parts, Machine
Mount Valve
Part No. 965767
Aluminum Wetted Parts, Hand–held
Valve with internal air switch
Part No. 965768
Aluminum Wetted Parts, Hand–held
Valve with electric switch for remote
operation
Part No. 965786
Aluminum Wetted Parts, Automatic
Machine Mount Valve
Part No. 243482
Stainless Steel Wetted Parts,
Precision Swirl Orbiter Mounted with
8370A
Nozzle Accessory
Model 965768 shown
Part No. 243666
Stainless Steel Wetted Parts,
PrecisionFloR Control Valve
Machine Mount Valve
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
D This equipment is for professional use only.
INSTRUCTIONS
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure stated on the equipment or in the Technical Data
for your equipment. Do not exceed the maximum working pressure of the lowest rated component
in your system.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Do not use hoses to pull equipment.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 180_F (82_C) or below –40_F (–40_C).
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
D Never use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in this equipment. Such use could result in a serious chemical
reaction, with the possibility of explosion, which could cause death, serious injury, and/or substan-
tial property damage.
308876
3
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. Refer to Grounding on page 6.
D If there is any static sparking or you feel an electric shock while using this equipment, stop dis-
pensing immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being dispensed.
D Keep the dispense area free of debris, including solvent, rags, and gasoline.
D Extinguish all open flames or pilot lights in the dispense area.
D Do not smoke in the dispense area.
D Do not turn on or off any light switch in the dispense area while operating or if fumes are present.
D Do not operate a gasoline engine in the dispense area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
4
308876
Features
D
Adjustable forward travel to reduce material surge when
valve opens
D
D
D
Compact size for small X–Y tables, working areas, and
robots
D
D
D
Severe-Dutyt needle and seat for longer operating life
Lubricated packings for longer seal life
Lightweight construction reduces operator/machinery
fatigue
Handle kit provides easy conversion from automatic to
manual usage
Stainless steel housing to handle most materials
4 Control Configurations
1. 1/8 npt(f) ported manifold block
2. Direct solenoid mount with speed control
3. Handle kit with 4-way air valve
4. Handle kit with electric switch
Travel adjustment (Model 965766,
965767, 965768, and 965786 only)
Accessory flow control fittings
to adjust open/close speed.
Replaceable nylon bearings
Divorced air section
Shaft is free to align
Hard chrome/stainless steel shaft
Urethane u-cup secondary seals
Self centering plastic bearing
Proven primary seals
Hardened stainless steel needles
Reversible carbide seat for severe duty
Aluminum or stainless wetted housings
Snuff back restrictor ring (13) is removable
for high flow applications.
8374B
8374A
Fig. 1
308876
5
Installation
NOTES:
D Fluid supply container: ground according to your
local code.
D Reference numbers and letters in parentheses in
the text refer to the callouts in the figures and
drawings.
D Flammable liquids in the spray area: must be in
approved, grounded containers. Do not store more
than the quantity needed for one shift.
D Accessories are available from your Graco
representative. If you supply your own accessories,
be sure they are adequately sized and
D All solvent pails used when flushing: ground
according to local code. Use only metal pails, which
are conductive. Do not place the pail on a
non-conductive surface, such as paper or
cardboard, which interrupts the grounding
continuity.
pressure-rated to meet the system’s requirements.
Grounding
WARNING
D To maintain grounding continuity when flushing or
relieving pressure, hold a metal part of the valve
firmly to the side of a grounded metal pail, then
trigger the valve.
FIRE AND EXPLOSION HAZARD
To reduce the risk of fire, explosion, and
serious injury, proper electrical ground-
ing of every part of your system is es-
sential. Read the warning section Fire
and Explosion Hazard on page 4, and
follow the grounding instructions below.
How to Use the Valve Trigger Safety
WARNING
SKIN INJECTION HAZARD
To prevent accidental triggering of the
gun and reduce the risk of a serious inju-
ry, including fluid injection or splashing in
the eyes or on the skin, lock the gun trigger safety
when you stop dispensing.
The following grounding instructions are minimum
requirements for a basic dispensing system. Your
system may include other equipment or objects which
must be grounded. Check your local electrical code for
detailed grounding instructions for your area and type
of equipment. Your system must be connected to a
true-earth ground.
1. If you are using one of the hand-held versions of
the valve, lock the valve trigger safety by turning
the latch to a right angle with the gun body. See
Fig. 2.
D Pump: ground the pump by connecting ground wire
and clamp as described in your separate pump
instruction manual.
2. To unlock the valve trigger safety, push the latch
out and turn it parallel with the gun body.
D Air compressors and hydraulic power supplies:
ground the equipment according to the
manufacturer’s recommendations.
D Fluid hoses: use only grounded fluid hoses with a
maximum of 500 feet (150 m) combined hose
length to ensure grounding continuity. Check the
electrical resistance of your fluid hoses at least
once a week. If your hose does not have a tag on it
which specifies the maximum electrical resistance,
contact the hose supplier or manufacturer for the
maximum electrical resistance limits, replace the
hose immediately.
Locked
Fig. 2
Unlocked
D Dispensing valve: ground the valve by connecting it
8459A
to a properly grounded fluid hose and pump.
6
308876
Installation
Machine Mount Valve
Connections
Install a remote 4-way air control valve to operate the
valve. Connect an open air signal air line to the 1/8
npt(f) OPEN port. Connect a close air signal air line to
the 1/8 npt(f) CLOSE port.
D The fluid inlet is 1/4 npt(f).
D The fluid outlet is 1/4 npt(f) or 3/4–16 unf(m).
D Air inlets are 1/8 npt(f).
Air Switch Hand Held Valve
D See Accessories, page 25, to order air control
This valve has a single air inlet and an internal 4-way
spool valve, which directly operates the air piston.
Connect the air line to the 1/8 npt(f) air inlet.
valves and tubing.
Electric Switch Hand Held Valve
Install a remote 4-way air control valve to operate the
valve. Connect an OPEN air signal air line to the 1/8
npt(f) port on the side of the valve. Connect a CLOSE
air signal air line to the 1/8 npt(f) port on the opposite
side of the valve. Wire the normally open valve switch
to the system control.
1
2
3
Solder to terminals in cable connectors as shown in Detail A.
Normally open, momentary contact switch.
Ground connection.
Detail A
2
3
1
Electric Switch Hand Held Valve shown
8370A
Fig. 3
308876
7
Operation
Electric Switch Hand Held Valve
WARNING
D Be sure the air supply lines are connected correctly
COMPONENT RUPTURE HAZARD
To reduce the risk of over-pressurization,
which can cause component rupture and
serious injury, never exceed 3000 psi (21
MPa, 207 bar) fluid pressure, or 120 psi (0.84 MPa,
8.4 bar) air pressure to the valve.
to the OPEN and CLOSE valve air ports.
D To open or close the valve and maintain the open or
closed status, a minimum of 40 psi (280 kPa, 2.8
bar) air pressure must be supplied and maintained
at the OPEN or CLOSE port.
D The trigger only activates the electrical switch in the
Pressure Relief Procedure
handle, which turns the remote solenoid on and off.
WARNING
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
D Trigger the gun to turn the solenoid on. Release the
trigger to turn the solenoid off.
Machine Mount Valve
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
D Be sure the air supply lines are connected correctly
to the OPEN and CLOSE valve air ports.
D To open or close the valve and maintain the open or
closed status, a minimum of 40 psi (280 kPa, 2.8
bar) air pressure must be supplied and maintained
at the OPEN or CLOSE port.
D are instructed to relieve the pressure
D stop dispensing
D check or service any of the system equipment
D install or clean the nozzle
To open the valve:
1. Apply air pressure to the OPEN air port on the
valve, and remove air pressure from the CLOSE
air port on the valve.
1. Shut off the air to the dispense valve, if applicable.
2. Shut off the air to the supply pumps.
2. Maintain air pressure on the OPEN air port to keep
the valve open.
3. Close the bleed-type master air valve (required in
your system).
To close the valve:
1. Apply air pressure to the CLOSE air port on the
valve, and remove air pressure from the OPEN air
port on the valve.
4. Hold a metal part of the valve firmly to the side of a
grounded metal pail, and trigger the dispense
valve to relieve pressure.
2. Maintain air pressure to the CLOSE air port to
keep the valve closed.
5. Open the fluid drain valve (required in your
system), having a grounded metal container ready
to catch the drainage.
6. Leave the fluid drain valve open until you are ready
to dispense again.
If you suspect that the dispense needle or hose is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the needle retaining nut or hose end coupling
and relieve pressure gradually, then loosen completely.
Now clear the needle or hose.
8
308876
Operation
D
The valve is at full stroke when the hex nut
Air Switch Hand Held Valve
(44) is at the end of the adjustment shaft (42).
The valve operation is such that there are only two
valve conditions: either fully open or fully closed.
D
Adjusting the nut (44) on the shaft (42)
towards the valve, or clockwise, will reduce the
stroke length.
The valve is opened and closed by the internal air
control valve. Trigger the gun to open the valve.
Release the trigger to close the valve.
D
Adjusting the nut away from the valve, or
counterclockwise, will lengthen the stroke.
Shaft Stroke Adjustment (Models 965766,
965767, 965768, and 965786 only)
3. Tighten the hex nut (44) to the adjustment nut (43)
to set the adjustment.
Adjust the shaft stroke to balance the valve between
“snuff-back” and “push-out”.
42
44
D A long stroke will give maximum snuff-back but it
may cause push-out when the valve opens.
Shorten
Lengthen
D Shortening the stroke of the shaft will minimize the
material pushed out when the valve opens and will
also increase the material back pressure through
the valve.
43
To adjust the shaft stroke:
1. Loosen the hex nut (44) from the adjustment nut
(43).
2. Adjust the nut (44) along the adjustment shaft (42)
to the desired position.
8460
Fig. 4
Maintenance
To grease the valve:
Preventative Maintenance
1. Remove the grease fitting from one side of the
gun.
There is a grease filled secondary seal/bearing area on
the valve shaft. Every 10,000 cycles, or twice each
month, new grease should be flushed across this area.
Each valve has two flush grease fittings. A small
grease gun is provided with each valve.
2. Pump grease (Part No. 115982) across the valve
until clear grease comes out of the other side.
3. Reinstall the grease fitting.
308876
9
Troubleshooting
1. Relieve the pressure.
WARNING
SKIN INJECTION HAZARD
2. Check all possible causes to the problem before
disassembling the pump.
To reduce the risk of serious injury
whenever you are instructed to relieve
pressure, always follow the Pressure
Relief Procedure on page 8.
PROBLEM
CAUSE
SOLUTION
Valve does not open
Insufficient air pressure
Turn on or turn up air pressure.
Air not exhausted from behind air cylin- Use four-way, relieving-type air valve operator.
der piston
Shaft adjustment too far closed
Adjust the shaft stroke as instructed on page 9.
Turn on or turn up air pressure.
Valve does not close Insufficient air pressure
(leaks)
Air not exhausted from behind air cylin- Use four-way, relieving-type air valve operator.
der piston
Blockage between needle and seat
Remove and clean needle and seat.
Bad or missing gasket between seat Replace gasket (38).
and housing
Needle worn out
Replace needle and seat.
Remove and clean.
Higher than normal Nosepiece plugging up
back-pressure
10
308876
Service
(Models 965766, 965767, 965768, and 965786 only)
12. Remove the pin (7), o-ring (9), and piston o-ring
WARNING
(6).
SKIN INJECTION HAZARD
13. Use a 1/4 in. pin punch to knock out the bearings
(5) and o-rings (4).
To reduce the risk of serious injury
whenever you are instructed to relieve
pressure, always follow the Pressure
Air Switch Handle (if equipped)
Relief Procedure on page 8.
1. Remove the trigger (56).
Disassembly
2. Loosen the set screw above the trigger safety. Pull
off the handle (55).
1. Relieve all air and fluid pressure.
3. Remove the four retaining screws (60). Pull the
housing (50) and gasket (30) away from the air
cylinder (1).
2. Disconnect the valve from the system.
3. Remove the four nosepiece screws (15), and pull
the nosepiece (40) away from the valve. Remove
the snuff-back ring (41). See Fig. 5, page 14.
Air Valve
1. Unscrew the stem guide (58).
4. Use an 1/8 in. pin punch in the needle hole (A) to
unscrew the needle (27). If the shaft (3) spins,
insert a dowel pin in the shaft hole (B) to hold it
steady, then unscrew the needle (27).
2. Remove the trigger pin (59), o-ring (57), spool
(49), spacers (51, 52), o-rings (46, 48) and spring
(47).
3. Remove the bushing (53) from the housing (50)
with the screw (54).
5. Remove the seat (25), gasket (38), and o-ring
(39).
4. Remove the screws (60) and lock-washers (61)
from the air cylinder (1).
6. Remove the two fluid housing screws (23) and
remove the fluid housing (26). Remove the primary
fluid seal (22) from the fluid housing (26).
Electric Switch Handle (if equipped)
1. Disconnect the power from the gun.
7. Pull the bearing/lube housing (19) from the air
cylinder (1). Remove the bearing (21), bearing
o-ring (16), and secondary fluid seal (20). Remove
the grease fittings (18).
2. The switch, housing, and cable are not repairable.
Replace these parts as a complete assembly.
3. Remove the trigger (56).
8. Remove the C-clip (12) from the back of the air
cylinder (1). Push the shaft (3) into the air cylinder
to dislodge the air cylinder cap (11). Remove the
cap o-ring.
4. Loosen the setscrew above the trigger safety. Pull
off the handle (55).
5. Remove the four manifold retaining screws (60).
Pull the housing (50) and gasket (30) away from
the air cylinder (1).
9. Remove the internal C-clip (12). Push the shaft (3)
to dislodge the piston (10) assembly from the air
cylinder (1).
6. Remove the bushing (53) from the housing (50)
with the screw (54).
10. Remove the adjustment nut (44) from the shaft (3).
11. Remove the adjustment shaft (42) from the shaft
(3).
7. Remove the screws (60) and lock-washers (61)
from the air cylinder (1).
308876
11
Service
(Models 965766, 965767, 965768, and 965786 only)
Fluid Section
Reassembly
1. Lubricate the bearing (21), o-ring (16) and cup seal
Air Cylinder Section
(20). Put the o-ring (16) on the bearing. Carefully
insert the seal (20) into the bearing recess, with
the lips of the o-ring facing into the bearing. Be
careful not to damage the seal lips.
1. Lubricate the shaft o-rings (4) and the bearings (5)
with grease supplied in the repair kit. Insert o-rings
into the air cylinder (1) and air cap (11) cavities.
See Fig. 5.
2. Push the bearing (21) seal end first into the
housing (19). Be sure that the grease hole in the
side of the bearing lines up with the grease ports in
the housing (19).
2. Press the bearings (5) flush into the air cylinder
housing and air cap, trapping the o-rings (4).
3. Lubricate and reassemble the piston assembly;
piston (10), o-ring (9), dowel pin (7), adjustment
shaft (42), o-ring (6), and shaft (3). Use Loctiter
Primer N7649 and Loctiter TL242, 243, or
3. Holding the bearing (21) in place, push the bearing
assembly over the shaft (3).
equivalent (“blue” Loctite) when assembling the
adjustment shaft (42). Tighten the shaft to 15–20
in–lb (1.7–2.2 NSm). The shaft (3) should hang
with some play to be self-aligning in the bearing.
4. Lubricate the main fluid seal (22) and its cavity in
the housing (26). Carefully press the seal, lip-first,
into the housing.
5. Push the housing (26) and seal (22) over the shaft
(3) and up against the bearing housing.
4. Lubricate the air cylinder (1) ID with the grease
supplied. Push the piston (10) assembly into the
air cylinder.
6. Apply anti–seize lubricant (Loctite 56765 or
equivalent) to the fluid housing screws (23) and
loosely install the screws to retain the housings.
Do not tighten the screws yet.
5. Orient the air inlet manifold (2) (if used) as shown.
Match the gasket openings to the air ports.
7. Insert the gasket (38) and seat (25). These items
are reversible and can be installed in either
direction.
8. Use Loctite Primer N7649 and Loctite TL242, 243,
or equivalent (“blue” Loctite) when assembling the
needle (27) and tighten to 15–20 in–lb (1.7–2.2
NSm).
9. Apply air pressure to the CLOSE port, or to the
pneumatic trigger valve if installed. This will align
the shaft, seal, and bearing. Tighten the fluid
housing screws (23) oppositely and evenly to
40–45 in-lbs (4.5–5 NSm).
10. Install the nosepiece (40) with the PTFE o-ring
(39), screw (15), and snuff-back ring (41), if used.
The snuff-back ring has an internal bevel on one
end which faces into the nosepiece. Tighten the
nosepiece screws to 15–20 in-lbs (1.7–2.2 NSm).
12
308876
Service
(Models 965766, 965767, 965768, and 965786 only)
Air Valve (if equipped)
8. Orient the gasket (30) to the holes on the air
cylinder (1). Screw the air valve assembly to the
cylinder with the screws (60) and lock-washers
(61). TIghten the screws evenly to 15–20 in-lbs
(1.7–2.2 NSm).
1. Insert the spring (51) into the housing (50).
2. Lubricate and install an o-ring (46) into the
housing.
9. Screw the bushing (53) to the housing (50) with
the screw (54). Tighten the screw to 140–150
in-lbs (15.8–16.9 NSm).
3. Install a spacer (52), internal bevel first, into the
housing.
4. Lubricate and install two o-rings (46) and the
spacer (51).
10. Attach the handle (55) with the setscrew.
11. Attach the trigger (56) with the grease fittings (18).
12. Test that the trigger safety works properly.
Electric Switch
5. Lubricate and install a spacer (52) with the internal
bevel out, and o-ring (46).
6. Lubricate and install o-rings (48) on the spool (49).
Insert the spool with the nub facing out.
1. The switch, housing, and cable are not repairable.
Replace these parts as a complete assembly.
7. Lubricate the pin (59) and insert it into the guide
(58). Screw the guide with o-ring (57) into the
housing. Tighten it to 60–70 in-lbs (6.8–7.9 NSm).
2. The switch, housing, and cable assembly are not
user serviceable and must be replaced as an
assembly.
308876
13
Service
(Models 965766, 965767, 965768, and 965786 only)
1
4
4
4
4
5
47 46 48 49
58 59
8370A
2
60
51
52
57
50
61
53
4
4
56
6
54
8375B
55
4
4
4
4
4
4
4
2
7
3
8
11 12
6
7 5 4 3
28, 29 20 21 22 39 27
23
40
13, 14
15
B
A
44
42
2
9
10 30 19 18 16
38 25 41
26
1
4
7
4
4
4
4
5
6
Tighten to 15–20 in-lb (1.7–2.2 NSm). The shaft should hang
with some play to be self-aligning in the bearing.
Tighten to 60–70 in-lbs (6.8–7.9 NSm).
1
Screw the bushing (53) to the housing (50) with screw (54).
Tighten to 140–150 in-lbs (15.8–16.9 NSm).
2
3
4
Tighten to 15–20 in-lbs (1.7–2.2 NSm).
Apply Loctite Primer N7649 and Loctite TL242, 243, or
equivalent (“blue” Loctite).
7
Tighten oppositely and evenly to 40–45 in-lbs (4.5–5 NSm).
Lubricate with grease supplied in the repair kit.
Apply anti–seize lubricant (Loctite 56765 or equivalent).
8
8371A
Fig. 5
14
308876
Notes
308876
15
Parts
(Models 965766, 965767, 965768, and 965786 only)
30 12
42
44
43
11
15
1
2
(965766 &
965786 only)
6
7
9
10
5
4
19
18
3
28, 29
16
38
20
21
22
25
26
39
27
41
23
40
15
8371A
16
308876
Parts
Model 965766
Machine Mount Valve
Stainless steel wetted parts
Model 243482
Orbiter Mounted Valve
Stainless steel wetted parts
Model 965786
Automatic Machine Mount Valve
Aluminum wetted parts
Model 243666
PrecisionFlo Control Valve
Stainless steel wetted parts
Ref. Part No. Description
No.
Qty.
Ref. Part No. Description
No.
Qty.
1
2
3
4*
5*
6*
7*
9*
10
11
626702
626069
626068
156454
551181
154662
552164
157628
626703
626704
HOUSING, air cylinder
MANIFOLD, air control
SHAFT, air cylinder
O-RING, 010 buna-n
BEARING, air cylinder
O-RING, 222 buna-n
DOWEL PIN
O-RING, 006 buna-n
PISTON, air cylinder
CAP, air cylinder CAP, air
cylinder; Models 965766
and 965786 only
CAP, air cylinder; Models
243482 and 243666 only
CLIP, internal 1.75
SCREW, drive
PLATE, identification
SCREW, 10–32 x 0.375
O-RING, 014
fluoroelastomer
FLUSH GREASE FITTING
LUBE HOUSING
U-CUP, urethane/EPR
BEARING, lube
U-CUP, Polymitet/EPR
SCREW, 1/4–20 x 2.25
SEAT, C2 carbide
HOUSING, fluid; stainless
steel; Model 965766 and
243282 only
HOUSING, fluid; aluminum;
Model 965786 only
NEEDLE, hardened stain-
less steel
LABEL, skin injection haz-
ard
1
1
1
2
2
2
1
1
1
1
30*
31
35*
626057
104459
551186
GASKET, air cylinder
SCREW, 10–32 x 1.75
GREASE, 3 oz. tube (not
shown)
GUN, grease (not shown)
COUPLER, flush grease
(not shown)
GASKET, seat
O-RING, 014 PTFE
NOSEPIECE, stainless
steel; Models 965766 and
243666 only
NOSEPIECE; aluminum;
Model 965786 only
1
4
1
36
37
115982
551187
1
1
38*† 171860
39*† 104319
40
1
1
1
626732
626707
195957
1
1
196018
1
NOSEPIECE; stainless
steel; Model 243482 only
RING, snuff-back
12
13
14
15
552163
102817
552161
104371
2
2
1
4
1
41*
42}
626060
626708
1
1
SHAFT, adjustment Models
965766 and 965786 only
NUT, adjustment Models
965766 and 965786 only
NUT, full hex, 10–32 Mod-
els 965766 and 965786 only
NUT, jam, 10–32 Models
243482 and 2436666 only
16*† 103610
43
44
45
626709
100166
102920
1
1
1
18
19
551188
626705
2
1
1
1
1
2
1
1
20*† 551191
21* 626064
22*† 551190
23n 103926
25*
26
*
Included in Rebuild Kit 570268.
185467
626731
† Included in Section Seal Kit 570267.
Y Replacement Instruction and Warning Labels are
626706
1
1
1
1
available at not cost.
27*} 626062
28Y 188377
29Y 188378
} Use Loctite Primer N7649 and Loctite TL242, 243,
or equivalent (“blue” Loctite) when assembling this
part.
LABEL, read instruction
manual
n Use anti–seize lubricant (Loctite 56765 or
equivalent) when assembling 965766 and 965786.
Use Loctite TL242, 243, or equivalent (“blue”
Loctite) when assembling 243482 and 243666.
308876
17
Parts
63
(965768 only)
60
61
53
56
54
8375B
8370A
55
(965767 only)
47
46
48
49
58
59
51
52
57
50
8372A
18
308876
Service
(Models 243482 and 243666 only)
6. Remove the two fluid housing screws (23) and
WARNING
SKIN INJECTION HAZARD
remove the fluid housing (26). Remove the primary
fluid seal (22) from the fluid housing (26).
To reduce the risk of serious injury
whenever you are instructed to relieve
pressure, always follow the Pressure
7. Pull the bearing/lube housing (19) from the air
cylinder (1). Remove the bearing (21), bearing
o-ring (16), and secondary fluid seal (20). Remove
the grease fittings (18).
Relief Procedure on page 8.
8. Remove the C-clip (12) from the back of the air
cylinder (1). Push the shaft (3) into the air cylinder
to dislodge the air cylinder cap (11). Remove the
cap o-ring.
Disassembly
1. Relieve all air and fluid pressure.
2. Disconnect the valve from the system.
9. Remove the internal C-clip (12). Push the shaft (3)
to dislodge the piston (10) assembly from the air
cylinder (1).
3. Remove the four nosepiece screws (15), and pull
the nosepiece (40) away from the valve. Remove
the snuff-back ring (41). See Fig. 5, page 14.
10. Remove the pin (7), o-ring (9), and piston o-ring
(6).
4. Use an 1/8 in. pin punch in the needle hole (A) to
unscrew the needle (27). If the shaft (3) spins,
insert a dowel pin in the shaft hole (B) to hold it
steady, then unscrew the needle (27).
11. Use a 1/4 in. pin punch to knock out the bearings
(5) and o-rings (4).
5. Remove the seat (25), gasket (38), and o-ring
(39).
308876
19
Service
(Models 243482 and 243666 only)
Fluid Section
Reassembly
1. Lubricate the bearing (21), o-ring (16) and cup seal
Air Cylinder Section
(20). Put the o-ring (16) on the bearing. Carefully
insert the seal (20) into the bearing recess, with
the lips of the o-ring facing into the bearing. Be
careful not to damage the seal lips.
1. Lubricate the shaft o-rings (4) and the bearings (5)
with grease supplied in the repair kit. Insert o-rings
into the air cylinder (1) and air cap (11) cavities.
See Fig. 5.
2. Push the bearing (21) seal end first into the
housing (19). Be sure that the grease hole in the
side of the bearing lines up with the grease ports in
the housing (19).
2. Press the bearings (5) flush into the air cylinder
housing and air cap, trapping the o-rings (4).
3. Lubricate and reassemble the piston assembly;
piston (10), o-ring (9), dowel pin (7), o-ring (6), and
shaft (3). Tighten the jam nut (45) to 15–20 in-lb
(1.7–2.2 NSm). The shaft (3) should hang with
some play to be self-aligning in the bearing.
3. Holding the bearing (21) in place, push the bearing
assembly over the shaft (3).
4. Lubricate the main fluid seal (22) and its cavity in
the housing (26). Carefully press the seal, lip-first,
into the housing.
4. Lubricate the air cylinder (1) ID with the grease
supplied. Push the piston (10) assembly into the
air cylinder.
5. Push the housing (26) and seal (22) over the shaft
(3) and up against the bearing housing.
5. Orient the air inlet manifold (2) (if used) as shown.
Match the gasket openings to the air ports.
6. Apply Loctite Primer N7649 and Loctite TL242,
243, or equivalent (“blue” Loctite) to the fluid
housing screws (23) and loosely install the screws
to retain the housings. Do not tighten the screws
yet.
7. Insert the gasket (38) and seat (25). These items
are reversible and can be installed in either
direction.
8. Apply Loctite Primer N7649 and Loctite TL242,
243, or equivalent (“blue” Loctite) to needle (27)
and tighten to 15–20 in–lb (1.7–2.2 NSm).
9. Apply air pressure to the CLOSE port, or to the
pneumatic trigger valve if installed. This will align
the shaft, seal, and bearing. Tighten the fluid
housing screws (23) oppositely and evenly to
40–45 in-lbs (4.5–5 NSm).
10. Install the nosepiece (40) with the PTFE o-ring
(39), screw (15), and snuff-back ring (41), if used.
The snuff-back ring has an internal bevel on one
end which faces into the nosepiece. Tighten the
nosepiece screws to 15–20 in-lbs (1.7–2.2 NSm).
20
308876
Parts
(Models 243482 and 243666 only)
4
2
2
2
2
2
2
2
3
4
1
12
6
7 5 4 3 28, 29 20 21 22 39 27
23
40
13, 14
15
15
40
45
2
9
10 30 19 18 16
38 25
26
2
2
2
2
Tighten oppositely and evenly to 40–45 in-lbs (4.5–5 NSm).
Lubricate with grease supplied in the repair kit.
Tighten to 15–20 in lbs (17–22 NSm)
1
2
Model 243482
3
4
Apply Loctite Primer N7649 and Loctite TL242, 243, or equivalent
(“blue” Loctite).
Fig. 6
308876
21
Parts
(Models 243482 and 243666 only)
12
30
15
1
19
45
6
9
7
10
5
4
19
18
3
28, 29
16
38
20
21
22
25
26
39
27
41
23
40
40
31
31
Model 243482
8371A
22
308876
Parts
Model 965767
Hand Held Valve with Pneumatic Trigger
Aluminum wetted parts
See page 16 for illustration of items 1–44. See page 18 for illustration of items 46–62.
Ref. Part No. Description
No.
Qty.
Ref. Part No. Description
No.
Qty.
1
3
626702
626068
156454
551181
154662
552164
157628
626703
626704
552163
102817
552161
HOUSING, air cylinder
SHAFT, air cylinder
O-RING, 010 buna-n
BEARING, air cylinder
O-RING, 222 buna-n
DOWEL PIN
O-RING, 006 buna-n
PISTON, air cylinder
CAP, air cylinder
CLIP, internal 1.75
SCREW, drive, #0 x 0.25
PLATE, identification
O-RING, 014
fluoroelastomer
FLUSH GREASE FITTING
LUBE HOUSING
U-CUP, urethane/EPR
BEARING, lube
U-CUP, Polymitet/EPR
SCREW, 1/4–20 x 2.25
SEAT, C2 carbide
HOUSING, fluid; aluminum
NEEDLE, hardened stain-
less steel
LABEL, skin injection haz-
ard
LABEL, read instruction
manual
1
1
2
2
2
1
1
1
1
2
2
1
1
40
626707
626060
626708
626709
100166
106559
NOSEPIECE, aluminum
RING, snuff-back
SHAFT, adjustment
NUT, adjustment
NUT, full hex, 10–32
O-RING, No. 905
fluoroelastomer
SPRING
O-RING, 007
fluoroelastomer
SPOOL, 4-way
HOUSING, air valve
SPACER, u-shape
SPACER, air valve
BUSHING, handle
SCREW, 3/8–16 x 3/4
HANDLE
TRIGGER
O-RING, 0.5 x 0.6
fluoroelastomer
GUIDE, stem
PIN, trigger
SCREW, 10–32 x 0.8125
WASHER, lock, #10
PLUG, pipe, headless,
1/8 npt (not shown)
1
1
1
1
1
5
41*
42}
43
44
46
4*
5*
6*
7*
9*
10
11
12
13
14
47
48
106561
106560
1
3
49
50
51
52
53
54
55
56
57
178651
626056
178652
178653
626055
551204
626075
626083
106551
1
1
1
2
1
1
1
1
1
16*† 103610
18
19
551188
626705
2
1
1
1
1
2
1
1
1
20*† 551191
21* 626064
22*† 551190
23n 103926
25*
26
27*} 626062
28Y 188377
29Y 188378
58
59
60
61
62
178654
626053
119156
100020
104765
1
1
4
2
1
185467
626706
1
1
*
Included in Rebuild Kit 570268.
30*
31
35*
626057
104459
115982
GASKET, air cylinder
SCREW, 10–32 x 1.75
GREASE, 3 oz. tube (not
shown)
GUN, grease (not shown)
COUPLER, flush grease
(not shown)
1
4
1
† Included in Section Seal Kit 570267.
Y Replacement Instruction and Warning Labels are
available at no cost.
36
37
551189
551187
1
1
} Loctite Primer N7649 and Loctite TL242, 243, or
equivalent (“blue” Loctite) should be used when
installing this part.
38*† 171860
39*† 104319
GASKET, seat
O-RING, 014 PTFE
1
1
n Anti–seize lubricant (Loctite 56765 or equivalent)
should be used when installing this part.
308876
23
Parts
Model 965768
Hand Held Valve with Electric Switch
Aluminum wetted parts
See page 16 for illustration of items 1–44. See page 18 for illustration of items 53–63.
Ref. Part No. Description
No.
Qty.
Ref. Part No. Description
No.
Qty.
1
3
626702
626068
156454
551181
154662
552164
157628
626703
626704
552163
552161
104371
HOUSING, air cylinder
SHAFT, air cylinder
O-RING, 010 buna-n
BEARING, air cylinder
O-RING, 222 buna-n
DOWEL PIN
O-RING, 006 buna-n
PISTON, air cylinder
CAP, air cylinder
CLIP, internal 1.75
PLATE, identification
SCREW, 10–32 x 0.375
O-RING, 014
fluoroelastomer
FLUSH GREASE FITTING
LUBE HOUSING
U-CUP, urethane/EPR
BEARING, lube
U-CUP, Polymitet/EPR
SCREW, 1/4–20 x 2.25
SEAT, C2 carbide
HOUSING, fluid; aluminum
NEEDLE, hardened stain-
less steel
LABEL, skin injection haz-
ard
LABEL, read instruction
manual
1
1
2
2
2
1
1
1
1
2
1
4
1
36
37
551189
551187
GUN, grease (not shown)
COUPLER, flush grease
(not shown)
1
1
4*
5*
6*
7*
9*
10
11
12
14
15
38*† 171860
39*† 104319
GASKET, seat
1
1
1
1
1
1
1
1
1
1
1
4
2
1
O-RING, 014 PTFE
NOSEPIECE, aluminum
RING, snuff-back
SHAFT, adjustment
NUT, adjustment
NUT, full hex, 10–32
BUSHING, handle
SCREW, 3/8–16 x 3/4
HANDLE
40
41*
42}
43
44
53
54
55
56
60
61
63
626707
626060
626708
626709
100166
626055
551204
626075
626083
119156
100020
949706
16*† 103610
TRIGGER
18
19
551188
626705
2
1
1
1
1
2
1
1
1
SCREW, 10–32 x 0.8125
WASHER, lock, #10
SWITCH ASSEMBLY
20*† 551191
21* 626064
22*† 551190
23n 103926
25*
26
27*} 626062
28Y 188377
29Y 188378
*
Included in Rebuild Kit 570268.
† Included in Section Seal Kit 570267.
185467
626706
Y Replacement Instruction and Warning Labels are
available at not cost.
1
1
} Loctite Primer N7649 and Loctite TL242, 243, or
equivalent (“blue” Loctite) should be used when
installing this part.
30*
31
35*
626057
104459
115982
GASKET, air cylinder
SCREW, 10–32 x 1.75
GREASE, 3 oz. tube (not
shown)
1
4
1
n Anti–seize lubricant (Loctite 56765 or equivalent)
should be used when installing this part.
24
308876
Accessories
Plastic Tube Fittings to Connect Air Signals
Tube OD
1/8 NPT (M) Straight
1/8 NPT (M) 90º Swivel
Tube Tee
1/8 in.
5/32 in.
1/4 in.
598329
104172
513826
598140
597151
551203
514435
111167
Tube OD
1/4 NPT (M) Straight
1/4 NPT (M) 90º Swivel
5/32 in.
1/4 in.
598252
104165
598327
C19391
Plastic Tubing for Air Signal Lines
4-Way Solenoids and Solenoid
Accessories
Part No.
Description
626144 Manifold
513063
514607
C12509
1/8 in. O.D. Nylon
5/32 in. O.D. Nylon
1/4 in. O.D. Nylon
To direct mount solenoid to 1K Ultra–Lite Valve.
551316 120 Volt ac Solenoid
For use with 626144 Manifold.
Air Signal Accessories
551201 Air Cylinder Speed Control 90_ Fitting
551317 24 Volt dc Solenoid
1/8 npt(f) inlet, 1/8 npt(m) outlet
For use with 626144 Manifold.
Mount on CLOSE port to control opening speed for
soft start. Mount on OPEN port to control closing
speed for less snuff–back.
551347 120 Volt ac Solenoid
Remote mount, 1/8 npt (f) ports
104661 Quick Exhaust Valve
551348 24 Volt dc Solenoid
1/8 npt(f) inlet and outlet, 1/4 npt(f) exhaust
Remote mount, 1/8 npt(f) ports
Used to speed up opening or closing action of the 1K
Ultra–Lite Valve
551349 120 Volt ac Din Plug
With screw terminals for above solenoids
104632 Pump Pilot Valve
551350 24 Volt dc Din Plug
1/2 npt (f) line ports, 1/8 npt(f) pilot port
With screw terminals for above solenoids
3–way air piloted air valve to turn air powered
proportioning pump on with hand gun signal.
Optional Main Fluid Needle Packings (22)
Part No.
551192
Description
Urethane U–Cup with EPDM o–ring
spreader
551193
Reinforced PTFE U–Cup with 302
stainless steel spreader
308876
25
Accessories
Fluid Nozzles
168683 Nozzle Bushing
Zinc-plated steel nozzles, 1/8 npt*
Zinc-plated steel, 1/8 npt
Kits
Part No.
607665
161505
164799
Orifice
Length
0.125 in. (3.17 mm) 2 in. (51 mm)
0.09 in. (2.28 mm) 2 in. (51 mm)
0.055 in. (1.39 mm) 2-1/8 in. (54 mm)
949631 Conversion Kit
Pneumatic 4–way valve with housing, handle, and
trigger and other parts necessary to convert 965766 or
965786 to a hand held valve.
*
Requires a 1/8 npt(f) bushing. Order 168683 Nozzle
Bushing.
949632 Conversion Kit
Electric switch style handle kit to convert 965766 or
965786 to a hand held valve.
Nozzles for use with 188253
flange nut.
570267 Seal Kit
With Polymitet main packing (standard)
8462A
570268 Rebuild Kit
With Polymitet main packing (standard)
Part No.
C00005
C00007
C00008
C00009
C00010
C00011
C00012
C00013
C00014
C00015
Orifice
Length
0.187 in. (4.75 mm) 1.656 in. (42 mm)
0.093 in. (2.36 mm) 2 in. (51 mm)
0.250 in. (2.28 mm) 2 in. (51 mm)
0.172 in. (4.37 mm) 2 in. (51 mm)
0.062 in.(1.57 mm) 2 in. (51 mm)
0.375 in. (9.53 mm) 2 in. (51 mm)
0.156 in. (3.96 mm) 2 in. (51 mm)
0.046 in. (1.17 mm) 2 in. (51 mm)
0.031 in. (0.79 mm) 2 in. (51 mm)
0.156 in. (3.96 mm) 1.812 in. (46 mm)
570299 Seal Kit
With PTFE main packing (optional)
570300 Rebuild Kit
With PTFE main packing (optional)
512135 Plastic Fluid Nozzle
1/4 npt, 0.062 in. (1.57 mm) orifice, 2-1/2 in.
(63.5 mm) long
26
308876
Technical Data
Category
Data
Maximum Fluid Pressure
Maximum Cylinder Air Pressure
Air inlets (open and close ports)
Fluid Inlet
4000 psi (28 MPa, 276 bar)
120 psi (0.84 MPa, 8.4 bar)
1/8 npt(f)
1/4 npt(f)
Fluid Outlet
1/4 npt(f) and 3/4–16 unf(m)
20 cps to 1 million cps
Isolation chamber with zerk fittings
Piston cylinder, EP o-rings
Fluid Viscosity Range
Snuffer Action Fluid Section
Divorced Air Cylinder
Weight
Aluminum Valve
Stainless Steel Valve
Handle Kit
1.43 lb (0.65 kg)
2.07 lb (0.94 kg)
0.77 lb (0.35 kg)
Wetted Parts
Aluminum Valve
aluminum, 303 stainless steel, 17–4 PH stainless steel, C2 car-
bide, hard chrome, ethylene propylene, Parker Polymitet, PTFE
Stainless Steel Valve
303 stainless steel, 17–4 PH stainless steel, C2 carbide, hard
chrome, ethylene propylene, Parker Polymitet, PTFE
Severe-duty Components
Shaft
Snuffer Needle
Seat
Shaft Seal, standard
Shaft Seal, optional
Hard chrome over 303 stainless steel
Hardened 440–C stainless steel
Reversible, solid C2 carbide inserts
High density Parker Polymitet
PTFE
Loctiter is a registered trademark of the Loctite Corporation.
308876
27
Dimensions
2.25 in.
(57.15 mm)
1.75 in.
(44.45 mm)
0.88 in.
(22.35 mm)
1.75 in.
(44.45 mm)
6.13 in.
(155.7 mm)
3.5 in.
(88.9 mm)
1.63 in.
(41.4 mm)
1.42 in.
(36.07 mm)
5 in.
(127 mm)
2.25 in.
(57.15 mm)
Direct Mount Solenoid
(optional)
8370A
28
308876
Notes
308876
29
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers
to identify the distributor closest to you:
1–800–328–0211 Toll Free
612–623–6921
612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 308876
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 1998, Graco Inc. is registered to ISO 9001
Revised 04/2009
30
308876
|
Graco Inc Pressure Washer 308 523 User Manual
Grizzly Chipper G0595 User Manual
Grundig Home Theater System DR 3400 DD User Manual
Hasbro Robotics 81327 User Manual
Honeywell Network Card 9782 Series User Manual
Hotpoint Double Oven KSO33CX S User Manual
HP Hewlett Packard Weather Radio HP 16532A 1 User Manual
Hunter Fan Outdoor Ceiling Fan 25860 User Manual
IBM Printer 1NA User Manual
iHome Speaker System iHM10 User Manual