Belt Mount Sled
Wearable Solution for Dolphin 70e Black
Quick Start Guide
www.honeywellaidc.com
HWC-BELT-WEH-QS Rev A
12/14
Getting to Know the Belt Mount Sled
Power Button
Audio Cable
End Cap
Sled
Lock
Scan Button
(not used with
Back Button
End Button
Bluetooth Ring Scanner)
Home Button
Send Button
Front Microphone
The sled encases theDolphin 70e Black including the touch panel and helps
protect the terminal from impacts.
Dolphin 70e Black Features Not Used
When the Dolphin 70e Black is installed in the belt mounted sled, the following
features are not available:
•
•
•
Touch screen display
Micro-USB port
Internal scanner.
Removing the Dolphin Black from the Sled
1. If the audio end cap is used, remove the audio cable.
To prevent damage to the Dolphin 70e Black always
unplug the audio cable before removing the end cap.
2. Slide the lock down to release the
end cap.
3. Push up on the right side of the end cap. Do not
attempt to remove the end cap without opening the
lock first!
4. Pull the end cap off of the sled.
5. Slide the Dolphin 70e Black out of the sled.
Use the notch in the bottom of the sled to
push the Dolphin 70e Black.
Removing the Battery
1. Remove the Dolphin 70e Black from the sled before changing the bat-
tery.
2. Place the terminal in Suspend mode by pressing and releasing the
Power button
.
3. Perform the steps illustrated below to remove the battery.
2
3
4
5
1
Installing the Battery
The Dolphin 70e Black model designed for use with the wearable sled uses
battery part numbers BAT-STANDARD-02 (Li-ion 3.7 V, 6.179 watt hour) and
BAT-EXTENDED-02 (Li-ion 3.7 V, 12.358 watt hour) manufactured for
Honeywell International Inc.
Note: Standard model battery
and battery door shown.
2
1
4
3
5
6
We recommend use of Honeywell Li-ion battery packs. Use of any non-
Honeywell battery may result in damage not covered by the warranty.
!
Turning Power On
To turn the terminal On, press and release the Power button
.
Suspend Mode
Press and release the Power button
Suspend Mode.
to toggle the terminal in or out of
Because the display is hidden in the belt mount sled, observe the backlights
for the Send, Home, Back and End keys. When the Dolphin 70e Black is on,
these keys are backlit. If the keys are not backlit, the terminal is Off or in
Suspend mode.
Note: You should always place the terminal into Suspend mode before removing
the battery.
Pairing the Bluetooth Ring Scanner (Optional)
Prior to this step, the system administrator must have configured EZ Pairing.
Pair the Bluetooth Ring Scanner before placing the terminal in the sled.
1. Touch
> Power Tools > EZ Pairing.
2. The EZ Pairing bar code is displayed on
the screen. If using a 2D imager ring
scanner, scan the on-screen bar code or
the bar code label on the back of the
terminal with the Bluetooth Ring Scanner.
If using a 1D ring scanner, scan the bar
code from the label on the back of the terminal.
3. Listen for the confirmation beeps.
4. Confirm the scanner is connected by observing the EZ Pairing icon on
the terminal display. When the icon is green, the scanner is connected .
If the icon is red, the scanner is not connected. Scan the bar code again.
5. If the scan wedge icon is displayed, scan wedge is running. If the scan
wedge icon is not displayed, Touch
> Power Tools > ScanWedge
NGW. Tap Yes if a message is displayed about continuing without a
tethered scanner connected.
EZ Pairing icon
Scan Wedge NGW icon
Placing Dolphin 70e Black into the Sled
1. If the end cap is installed on the
sled, slide the lock down to release
the end cap.
2. Push up on the right side (the side with the lock) of end
cap. Do not attempt to remove the end cap without
sliding the lock first!
3. Pull the end cap off the sled.
4. Make sure the USB door is closed. Rotate the door
on the right side of the Dolphin 70e Black to close.
5. Press until the door is flush with the side of the
terminal.
6. Slide the Dolphin 70e Black into the sled.
7. Make sure audio jack door is open. Pull the
rubber door out and rotate the door 180º as
shown to prevent damage.
8. Make sure the audio cable is not installed in the end cap.
9. Slide the end cap straight onto the sled until it clicks in
place.
10. Slide the lock closed to secure the end cap.
Attaching the Headset
1. Make sure the audio jack door is open as shown in the previous section.
2. Slide the 3.5mm audio connector into the end
cap.
3. Attach the quick disconnect end
of the headset adapter cable to
the headset’s cable.
4. Slide the cable ends together until they click.
Do not twist or bend the connectors.
Attach the Sled to the Belt Clip
1. Align the sled assembly with the belt clip
and press on the sled until it latches onto
the belt clip. Be sure to align tabs on the
back of sled with the notches on the belt
clip.
2. Slide the clip over a belt to wear the assembly.
Technical Assistance
Contact information for technical support, product service, and repair can be
User Documentation
For localized versions of this document, and to download the User’s Guide,
Limited Warranty
warranty information.
Patents
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether
any such changes have been made. The information in this publication does
not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the
furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated into another language without the prior written
consent of HII.
2014 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
|