quick start
1:power
2:antenna
3:insert
Attach AC adaptor plug to
jack on back of the unit and
plug the other end into a
wall socket.
Snap AM antenna into provided
stand, then plug antenna cable
into socket on back of unit.
Move antenna 12”away.
Place Zune insert in dock.
Never dock a Zune without
the proper insert in place.
4:Zune
5:radio
F
M
InsertaZune® into thedockwith
proper insert (Zune must not be in
a skin or case). The Zune will charge
while docked. Turn the Function
knob to Zune and press play on your
Zune to play it .
Turn the Function knob to AM
or FM to select AM or FM radio
band.Turn the Tuning knob to
desired radio station.
1
Controls and Indicators
ꢁ Dock
ꢃ Volume Knob
Power ON LED
ꢂ Tuning Knob
ꢄ Function Knob
AM Loop ᕥ
Antenna socket
Aux-in Jack ᕦ
Headphones Jack ᕧ
EXB switch ᕨ
ꢀ AC Adaptor Jack
FM Antenna
2
Using Your iHome
Connect Unit to Power Source
Plug the AC adaptor cable into the ꢀ AC Adaptor Jack on the back of the unit and the other end into a standard 120VAC
wall outlet.
Install Zune Insert
Your unit comes with a removable insert to ensure your Zune fits properly in the ꢁ Dock.
USE PROPER INSERT TO AVOID DAMAGE TO Zune OR UNIT.
Playing and charging your Zune
1. Place proper insert for your Zune in ꢁ Dock, then gently dock Zune. When docked, Zune will charge until fully charged.
The Zune will not overcharge.
2. Turn the ꢄ Function Knob to Zune and press play on Zune to play.
3. Turn the ꢃ Volume Knob clockwise to turn on the unit (Power On LED will light) and adjust the volume. Set the ᕨ EXB
Switch to On for sound boost.
4. To switch off the unit, turn the ꢃ Volume Knob fully counter-clockwise.
Listening to Radio
Setting Up Antennas
1. Snap AM loop antenna into provided stand, then plug antenna cable into the ᕥ AM Antenna socket on back of the unit.
Move antenna 12” away from the unit and rotate it for best reception.
2. Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antenna.
Tuning and Playing the Radio
1. Turn the ꢄ Function Knob to AM or FM to select AM or FM radio band.
2. Turn the ꢃ Volume Knob clockwise to turn on the unit (Power On LED will light) and adjust the volume. Set the ᕨ EXB
Switch to On for sound boost.
3. Turn the ꢂ Tuning Knob to tune radio to the desired station.
4. To switch off the unit, turn the Volume Knob fully counter-clockwise.
Using the Aux-in Jack
1. Plug one end of the audio patch cord (included) into the headphone or line-out jack on your nondocking Zune or other
audio device and the other end of the patch cord into the ᕦ Aux-in Jack located on the back of the unit.
2. Turn the ꢄ Function Knob to AUX.
3. Turn the ꢃ Volume Knob clockwise to turn on the unit (Power On LED will light) and adjust the volume. Set the ᕨ EXB
Switch to On for sound boost.
4. To switch off the unit, turn the Volume Wheel fully counter-clockwise.
Using the Headphones Jack
1. Plug your headphones into the ꢅ Headphones Jack located on the back of the unit for private listening to any selected
function (Zune, radio or aux). Speaker output is disabled when headphones are plugged in.
2. Turn the ꢃ Volume Knob clockwise to turn on the unit (Power On LED will light) and adjust the volume. Set the ᕨ EXB
Switch to On for sound boost.
3. To switch off the unit, turn the Volume Knob fully counter-clockwise.
3
A Consumer Guide to Product Safety
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety.
However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating
instructions carefully before installation and use, and keep these instructions handy for future reference. Take special
note of all warnings listed in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings.
Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of
air through the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the
unit to where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for
cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any
openings or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or
cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will
prevent damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A.
B.
C.
D.
E.
the power supply cable or plug has been damaged.
objects have fallen into or liquid has been spilled into the enclosure.
the unit has been exposed to rain.
the unit has been dropped or the enclosure damaged.
the unit exhibits a marked change in performance or does not operate normally.
12. Antenna – Do not connect an external antenna to the unit (other than that provided).
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the
power cable should be unplugged from the unit to prevent damage or corrosion.
14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service
personnel.
4
Troubleshooting
Possible Problem
Solution
Symptom
Unit does not respond AC adaptor isn’t plugged into a wall outlet or Plug the AC adaptor into a wall outlet and plug the connector into
the connector is not plugged into the power the supply jack on the unit. Turn Volume knob to turn unit on.
supply jack on the back of the unit
Wall outlet is not functioning
Plug another device into the same wall outlet to confirm the outlet
is working. If the outlet is controlled by a switch, turn switch on.
Zune cannot dock
properly
Using no or wrong Zune insert
Zune isn’t installed properly
Make sure the dock insert is the proper fit to your Zune
Remove your Zune from the dock and check for obstruction on the
connectors in the dock and on your Zune. Then reseat it in the dock.
Zune is playing but
there’s no sound
Zune is not installed properly
Remove your Zune from the dock and check for obstruction on
the connectors in the dock and on your Zune. Then reseat it in
the dock.
Function knob is not set to Zune
Zune is locked up
Make sure Function knob is set to Zune
Please make sure your Zune is working properly before docking
into the unit. Please refer to your Zune manual for details.
Remove your Zune from the dock and check for obstruction on
the connectors in the dock and on your Zune. Then reseat it in
the dock.
Zune didn’t charge
Sound is distorted
Zune is not installed properly
Zune is locked up/frozen
Zune battery has problem
Volume level is set too high
Sound source is distorted
Please make sure your Zune is working properly before docking
into the unit. Please refer to your Zune manual for details.
Decrease the unit volume and set EXB switch to off
If Zune original sound source is poor quality, distortion and noise
are easily noticed with high-power speakers.
Try a different audio source such as a music CD.
Plug the AM loop antenna connector to the jack on the back of
the unit. Move the loop antenna away from the unit. Rotate
antenna for best reception.
No AM radio sound
OR very noisy
AM radio sound
AM loop antenna is not connected to the
unit OR is not properly located
5
Solucionando problemas
Síntoma
Causa posible
Solución
La unidad no
responde.
El adaptador de AC no está conectado al
tomacorriente o el conector no está
conectado a la ficha en la parte posterior de
la unidad.
Conecte el adaptador de AC a un tomacorriente y el adaptador
a la ficha en la parte posterior de la unidad.
Gire el control de volumen para encender la unidad.
El tomacorriente no funciona.
Conecte otro aparato en ese tomacorriente para verificar si el
tomacorriente funciona. Si el tomacorriente funciona con un
interruptor, colóquelo en la posición de encendido.
El Zune no encastra No ha colocado ningún encastre o ha Verifique que el encastre sea el apropiado para su Zune.
correctamente.
colocado el encastre incorrecto para su Zune.
El Zune no encastró correctamente.
Quite el Zune del encastre y retire la posible obstrucción del
encastre o de su Zune. Vuelva a colocar el Zune dentro del
encastre.
El Zune está
funcionando pero no
hay sonido alguno.
El Zuneno está instalado correctamente.
Quite el Zune del encastre y verifique posibles obstrucciones del
encastre o de su Zune. Vuelva a colocar el Zune dentro del
encastre.
El control de función Zune no ha sido Coloque el control de función Zune en la posición Zune.
seleccionado
El Zune está trabado.
Verifique que su Zune funciona correctamente antes de conectarlo
a la unidad. Refiérase al manual de su Zune para más detalles.
El Zune no cargó.
El Zune no está instalado correctamente.
Quite el Zune del encastre y retire la posible obstrucción del
encastre o de su Zune. Vuelva a colocar el Zune dentro del
encastre.
El Zune está trabado/no responde.
Por favor asegúrese de que su Zune funciona correctamente
antes de colocarlo en el encastre. Refiérase al manual de su
Zune para mayor información.
La batería del Zune podría tener algún
inconveniente.
El sonido sale El volumen se encuentra muy alto.
distorsionado.
Baje el volumen de la unidad y coloque el selector EXB en
apagado.
El sonido de la unidad sale distorsionado.
Si el sonido original era de pobre calidad, las distorsiones y ruidos
se harán más notables con los parlantes de alta potencia. Pruebe
utilizar otra fuente de audio como un CD de música.
No se escucha la La antena circular no se encuentra conectada Inserte el conector de la antena circular a la ficha en la parte
radio AM o el sonido a la unidad o no está ubicada correctamente. posterior de la unidad. Aleje la antena de la unidad. Gire la antena
de la radio AM sale
muy distorsionado
hasta obtener una mejor recepción.
6
Limited 90-Day Warranty Information
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from
defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service
Center listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase
is $20.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries
are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($20.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Dr.
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies product.
Toll Free Customer Service: 1-800-288-2792
ZN10_ZN14 IB-042407-A
©SDI Technologies 2007 All rights Reserved
Printed in China
|